WS-7394U-IT Wireless 915 MHz Wireless Weather Station Instruction Manual
104. “RCC” will appear above the indoor temperature/humidity display and “ON” or “OFF” will flash above that. 5. Press and release the “OUT/+” butt
11 H. Setting The Minutes Manually 1. Press and hold the “SET” button for five seconds. 2. “lcd” will appear at the top of the display and a numb
123. Press and release the “SET” button nine more times to advance to the Manual Date setting. 4. The date will begin to flash below the time displ
133. Press and release the “SET” button twelve more times to advance to the Relative Pressure setting. 4. The barometric air pressure will flash in
14 FEATURES AND OPERATIONS A. Minimum and Maximum Temperature and Humidity 1. Indoor Minimum and Maximum Temperature and Humidity The indoor we
15Note: To reset the outdoor minimum and maximum temperature, first display the values you wish to reset (minimum or maximum). Next press and hold
16b. The minimum and maximum temperature of the additional remote sensor can be displayed by pressing the “OUT/+” button. c. To reset the minimum a
172. The icons change in order, from “sunny” to “sun with clouds” to “clouds with rain” or the reverse. 3. It will not change from “sunny” directly
18 Note: For accurate barometric pressure trends, the Weather Station should operate at the same altitude for example, it should not be moved from
19a. With a nonabrasive solution, clean and dry the back of the mounting bracket and the mounting surface to ensure a secure hold. The mounting sur
2TABLE OF CONTENTS Topic Page Inventory of Contents/ Additional Equipment 3 About WWVB 3 Quick Set Up Guide 4 Detailed Set Up Guide
20D. Immediately remove all low powered batteries to avoid leakage and damage. E. Opening the casings invalidates the warranty. Do not try to repa
21Outdoor -39.8°F to 139.8°F with 0.2°F resolution (-39.9°C to 59.9°C with 0.1°C resolution) (“OFL” displayed if outside this range) Relative humidit
22Technology, Ltd authorized service center. La Crosse Technology, Ltd will pay ground return shipping charges to the owner of the product to a USA
23FCC ID: OMOTX29U (sensor) RF Exposure mobile: The internal / external antennas used for this mobile sensor must provide a separation distance of at
1WS-7013U-IT Wireless 915 MHz Temperature Station Instruction Manual
2TABLE OF CONTENTS Topic Page Inventory of Contents Quick Setup Detailed Setup Guide Battery Installation Setting the Time Features Minimu
3 INVENTORY OF CONTENTS 1. The indoor temperature station (Figure 1) 2. The remote temperature sensor (TX29U-IT) and mounting br
4 ADDITIONAL EQUIPMENT (not included) 1. 1 Philips screwdriver. 2. 2 Fresh AAA 1.5V batteries. 3. 2 Fresh AA 1.5V batteries Q
53. Place the batteries into the remote temperature sensor first then into the indoor temperature station. (All remote temperature sensors must be
6walls, floors, ceilings, thick trees, etc.) will effectively cut signal range in half. Example: A wireless weather station with a 330 feet rang
3 INVENTORY OF CONTENTS 1. WS-7394U-IT— Wireless Weather Station (Figure 1) 2. TX29U-IT—remote temperature sensor (figure 2) 3. Instr
7To complete the set up of your indoor temperature station after the 15 minutes have passed please follow the steps below. 1. Press and hold the “
86. When the correct hour is shown, press and release the “SET” button once. Press and release the SET button once more and you are done. DETAI
9data signal from the sensor. The outdoor temperature and humidity should then be displayed on the Temperature Station. If this does not happen afte
10a. Remove the battery cover on the backside. To do this, push up and pull out. b. Observing the correct polarity, install 2 AAA
11 * When the signal is successfully received by the Temperature Station, the icon will be switched on. (If not successful, the icon w
12910MHz. This will also be done for re-synchronization. SETTING THE TIME 1. Press and hold the “SET/CH” button for 5 second, “12h” will appear
13 Note: if “12h” is selected, the temperature is displayed in degree Fahrenheit. If “24h” is selected, the temperature is displayed in degree Celsi
14temperature sensor units with the WS-7013U-IT. These extra sensors can be purchased through the same dealer as this unit. 1. Remove all the bat
155. Insert the batteries to the second sensor as soon as the outdoor temperature readings from the first sensor are displayed on the Temperature s
16NOTE: You must insert the batteries into the third sensor within 45 seconds of reception of the second sensor. IMPORTANT: Transmission problems w
4antenna in the Wireless Weather Station. However, due to the nature of the Earth’s Ionosphere, reception is very limited during daylight hours. Th
173. To reset the Minimum/Maximum readings, press and hold the “MIN/MAX” button for four seconds. MOUNTING Note: To achieve a true temperature re
18b. Mount using either screws or adhesive tape. c. Reattach the temperature sensor to the mounting bracket. 2. THE TEMPERATURE STATION e. The
19 Problem: The LCD is faint Solution: Replace batteries Problem: No outdoor temperature I displayed. Solution: 1) Remove all batteries, reinsert
20The indoor sensor is less responsive to ambient air currents because of the shielding effect of the display's case. In addition, the case can
219 Opening the casings invalidates the warranty. Do not try to repair the unit. Contact La Crosse Technology for repairs. SPECIFICATIONS Tran
22Indoor Temperature Station 2 x AAA, 1.5V Dimensions: (H x W x D) Indoor Temperature Station 4.3 x 2.75 x .92 in. (excluding table stand) (110
23authorized service center. The original dated bill of sale must be presented upon request as proof of purchase to La Crosse Technology, Ltd or La
24ground return shipping charges to the owner of the product to a USA address only. Your La Crosse Technology, Ltd warranty covers all defects in m
25misrepresentation by the seller or performance variations resulting from installation-related circumstances. LA CROSSE TECHNOLOGY, LTD WILL NOT A
26Fax: 608.796.1020 e-mail: [email protected] (warranty work) [email protected] (information on other products) web: www.
5 DETAILED SET-UP GUIDE I. BATTERY INSTALLATION (When one temperature sensor is being used) 1. First, insert the batteries to the temperature se
27 FCC ID: OMOTX29U (sensor) RF Exposure mobile: The internal / external antennas used for this mobile sensor must provide a separation distance of
28interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used i
6 * When the signal is successfully received by the Weather Station, the icon will be switched on. (If not successful, the icon will not be shown in
74. The time and date can be manually set. Once the signal is captured, it will override any time and date set to the time zone selected. 5. Once th
8 B. There are many different modes the indoor weather station can be set to. The LCD shown is the normal operating mode, and your actual data shown
94. Press and release the “SET” button to confirm the LCD contrast setting and continue to the Time Zone setting. C. Time Zone Setting 1. Press an
Comments to this Manuals