i WS-7054U Wireless 433 MHz Temperature Station Instruction Manual
7 II. TIME A. SETTING THE TIME 1. Press and hold the SET button for 1 second. “12h” will appear in the TIME LCD. 2. Use the INDOOR button to
8 5. Press the SET button to activate the clock. Note: There is only a “PM” display, which appears under “TIME.” If there is no display here it i
9 IV. FEATURES A. INDOOR MINIMUM AND MAXIMUM TEMPERATURES 1. Press and hold the INDOOR button for 1 second. “MIN” appears in the INDOOR LCD and
10 B. OUTDOOR MINIMUM AND MAXIMUM TEMPERATURES 1. Press and hold the OUTDOOR button for 1 second. “MIN” appears in the OUTDOOR LCD. The “OUTDOOR
11 displayed in the OUTDOOR LCD, and the time it was recorded is displayed in the TIME LCD. After 15 seconds the “OUTDOOR MAX,” and “TIME” will sto
12 temperatures are reset release the buttons. 2. To return to the current indoor temperature, press and hold the INDOOR button two times, holding
13 VI. READING THE TEMPERATURE TREND A. The temperature trend indicator is displayed in the OUTDOOR LCD. 1. Ï Indicates that the temperature is r
14 walls, concrete, and large metal objects can reduce the range. Place both units in their desired location before permanently mounting the Remote C
15 c) Where marked, drill holes into mounting surface using an appropriate size drill bit. d) Screw mounting bracket onto the mounting surface. Ens
16 c) Remove the protective strip from the other side of the tape. Position the Remote Control Sender in the desired location, ensuring that the Ind
ii TABLE OF CONTENTS Topic Page Inventory of Contents 1 Additional Equipment 1 Quick Setup 2 Detailed Setup Guide Battery Installation 3-6 Rem
17 1. USING THE TABLE-STAND a) The Indoor Temperature Station comes with the table stand already mounted. If you wish to use the table-stand all t
18 a) Remove the table stand. To do this, pull down on the stand from the rear and rotate forward. b) Fix a screw (not included) into the desired w
19 offers the same plus a 10’ probe to insert in a pool, spa, soil, etc.). Assign a number to each Remote Control Sender (i.e. #1 will be for outdoor
20 A. SETUP OF MULTIPLE UNITS 1. It is necessary to remove the batteries from all existing units in operation. 2. Remove the battery covers to al
21 1 5. Install batteries into the Indoor Temperature Station. (Refer to instructions in I.B.). 6. Follow directions in section II.A to set the tim
22 3. Repeat step 1 to view the 3rd, 4th, and 5th (depending on how many are set up) temperatures sent by the Remote Control Senders. Continue to pr
23 their minimum and maximum temperatures. 3. To reset the OUTDOOR MINIMUM AND MAXIMUM TEMPERATURES, follow step 1 above and the directions in sectio
24 TROUBLESHOOTING Problem Solution “--. -” appears in the OUTDOOR LCD of the Indoor Temperature Station. Batteries may be inserted wrong in Remote
25 “--.-” appears in the OUTDOOR LCD of the Indoor Temperature Station. (continued) Obstacles such as walls, concrete, metal window frames, or large
26 No temperature in the LCD of the Remote Control Sender. The batteries may be inserted wrong or weak—check the polarity of batteries or replace with
iii Remote Control Sender 13-16 Indoor Temperature Station 16-18 Using Multiple Remote Control Senders Setup of Multiple Units 18-21 Viewin
27 The LCD of the Indoor Temperature Station is blank. (continued) Contact La Crosse Technology for replacement. Temperature is “incorrect” Temperat
28 Problem not covered under the warranty (ie. Dropped unit into water). Call La Crosse Technology to order replacement part. We will accept Visa
29 • Opening the casings invalidates the warranty. Do not try to repair the unit. Contact La Crosse Technology repairs. SPECIFICATIONS Transmit
30 with 0.2 °F resolution. (-29.9 °C to 69.0 °C with 0.1 °C resolution). Accuracy Indoor +/- 2 °F (+/- 1 °C). Outdoor +/- 2 °F (+/- 1 °C)
31 Indoor Temperature Station 3.51 x 1.19 x 4.88 in. (excluding table stand) (90 x 30.5 x 125 mm). Remote Control Sender 2.18 x 0.94 x 3.12 in.
32 herein, with new or reconditioned parts or products if found to be defective during the limited warranty period specified above. All replaced part
33 other than an authorized La Crosse Technology, Ltd authorized service center; (6) units used for other than home use (7) applications and uses that
34 For warranty work, technical support, or information contact: La Crosse Technology 2809 Losey Blvd. S. La Crosse, WI 54601 Phone: 608.782.1610 Fax
35 FCC DISCLAIMER This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may no
1 INVENTORY OF CONTENTS 1. The Indoor Temperature Station (Figure 1) 2. The Outdoor Remote Control Sensor (TX3U) and mounting bracket. (Figure 2)
2 QUICK SETUP 1. Insert two AAA batteries into the Remote Control Sender. 2. Insert two AA batteries into the Indoor Temperature Station. 3. Wa
3 DETAILED SETUP GUIDE I. BATTERY INSTALLATION A. REMOTE CONTROL SENDER 1. Remove the mounting bracket. The bracket snaps on and off with mini
4 battery cover to fall away from the unit. Place the screw partially back into the hole and angle it slightly, so the threads grab the battery cover
5 B. INDOOR TEMPERATURE STATION Note: After the batteries are installed, DO NOT press any buttons. This may interfere with the signals, causing te
6 2. Observing the correct polarity, install 2 AA batteries. 3. Replace battery cover. 4. Wait 5-6 minutes or until both indoor and outdoor temper
Comments to this Manuals